should work fine, see the 3 or 4 posts in the forum link above. 

@QMaster thanks 

So, I'm spawning monsters after the start of a level. Not just hiding them and then turning them on later, but actually creating new monster entities.

This involves a lot of tricky with spawn functions and precaches, but it works fine (props to gb/Preach).

What doesn't work is incrementing the monster count properly.

I'm using a custom writebyte to do this:


total_monsters = total_monsters + 1;

WriteByte (MSG_BROADCAST,SVC_UPDATESTAT);
WriteByte (MSG_BROADCAST,STAT_TOTALMONSTERS);
WriteLong (MSG_BROADCAST,total_monsters);


Which also works fine, but only the first time a monster is spawned. After that it increments the counter by 2 instead of 1. It doesn't keep on incrementing, no matter how many more I spawn, it just sticks at +2 per spawn.

I'm trying various solutions, but it almost seems like there is some engine side value which is being affected invisibly.

I've traced back all the occurances of total_monsters = total_monsters + 1; I can find and no luck. I've also shifted where/how its incremented a few times and turned off various parts of the process to try and localise the issue, but no luck so far.

Yes, I have an exclusion in walkmonster_start so that doesn't also add to the count...

Any ideas? I'm tempted to make it so that spawned creatures just don't add to the count, meaning the player can get >100% kills, but that's a sloppy fix. 

Stupid mistake in walkmonster_start 

Can I make a recursive function? What is the maximum stack depth? 

You can create a recursive function, the maximum stack depth is 32. This is possible to hit, see http://tomeofpreach.wordpress.com/2013/08/09/going-overboard-with-field-pointers/ for an example and a bit more detail.

Spike posted a warning somewhere on here that local variables to a recursive function are not reset between calls. So you should initialise all your variables like you would in C when writing a recursive function, rather than assume they get initialised to zero. 

Thanks. 32 is very small for my task. I'll have to think of something else 

How much time can be in progess the function? Can the engine to break it off if it is too long time? 

The engine does have a limit, not strictly on time spent, but on number of instructions. You can only run 100,000 instructions in a single think, touch, spawn (etc) function before the QC concludes that there's a runaway loop and the engine packs it in. 

regarding locals getting clobbered in recursive functions, you can try '#pragma warning enable F302' to get fteqcc to print warnings when it detects that locals were not initialised before use.

fte/dp have a higher limit than 32.

you can get around the instruction limit by splitting up your routine into multiple thinks. in general your mod will be unplayable if you do not do this in the first place due to the stalls induced by running the qcvm.
in fte, there's some obscure 'sleep' builtin which will defer the current invocation/coroutine until a later time. doing this will preserve locals but not globals/fields. the instruction limit will be reset in the process. hurrah for infinite loops that won't lock up the game. just make sure nothing is harmed if some other think or whatever function removes the entities in the mean time... 

I thought it was 100000 instructions per frame. 

You get a new counter every time PR_ExecuteProgram is called, which means every time the engine calls a QC function of some kind.

They can even nest - suppose you are in a monster's think function, and use 50000 instructions before you call walkmove and collide with a player. You get a new lot of 100000 instructions to run the monster's collision function, then yet another set of 100000 to resolve the player's collision function, THEN you go back to the think function and get the remain 50000 instructions to wrap up there. 

ohhhh, nice to know i was being overly conservative then. this is like finding 20$ in my couch! 

Is it possible to return a string to a function that does traceline and returns the texturename of the wall that traceline hits. I understand that the entity returned would be world, but is it possible to get the texture name from the bsp surfacr? Like "brick2_4"? 

 

probably darkplaces has this. 

Check for extension DP_TRACE_HITCONTENTSMASK_SURFACEINFO

Then you can define:
string trace_dphittexturename;
then when you do a standard traceline, the texture name gets assigned to that variable.

One of the nice properties here is that there's no extra built-in function involved, so the code is very easy to make safe in engines which don't support the extension. In those engines, the texture name will always be "". So you can do stuff like special footsteps or impact particles on particular textures, and the other engines will gracefully degrade to the defaults for free! 

//----------------------------------------------------------------------
// Check for contact with sky brushes
//----------------------------------------------------------------------
float(vector targ_origin) check_pointcontent =
{
local float surfnum;
local string texturename;

surfnum = getsurfacenearpoint(world, targ_origin);
if (surfnum >= 0) {
texturename = getsurfacetexture(world, surfnum);
if (strncasecmp(texturename, "SKY", 3) == 0) return TRUE;
}
return FALSE;
}; 

float(vector targ_origin) check_pointcontent =
{
����return (pointcontents(targ_origin) == CONTENT_SKY);
} 

The latest version of DP does sky pointcontent detection different, hence the function, but a working example of detecting surface information can be adapted for what Qmaster wanted. ;) 

nt 

As ever yall are awesome. Thank you! 

That one was too easy for the masters. Here's a real stumper for you.

I want to simulate a halucinagenic side-effect for one of my power-ups in game. Here's how I want to achieve it, in psuedo code:

float TRIPPY_EFFECT_INTERVAL = 5.000 //5 seconds
// string "gfx/palette_trippy1.lmp"
// string "gfx/palette_trippy2.lmp"
// string "gfx/palette_trippy3.lmp"

void () trippydrug_think = {

if (trippydrug > FALSE)
{
setpalettefile("gfx/palette_trippy", trippydrug, ".lmp");
trippydrug++;
self.owner.trippy_power = (trippy_power * 2)
self.think = trippydrug_think;
self.nextthink = (time + TRIPPY_EFFECT_INTERVAL);

}

};

The 1st palette file will have the colors shifted over 4 colors so most things are similar to what they should be, then mixed up a little bit in the 2nd, with the 3rd palette file looking like crayola barf making it hard to see.

So... I can't find out how to change the palette on the fly within the engine code? I can override palette.lmp in the gfx folder, but... more than once, during runtime...? 

host_basepal or something stores the palette.lmp file in memory. mix that up with the "bf" command to figure out how the engine applies a new palette in a software renderer. or something.
in gl renderers things get much more messy, figure that one out on your own, if you dare. 

Its like a treasure hunt!